Are you looking for another fast and easy tablerunner tutorial?
Download the free PDF of this tutorial!
This Christmas Pinwheels table runner tutorial would be a perfect one to make and takes no time at all. I have directions to make this with rotary cutting or the AccuQuilt dies, keep reading!
Christmas Pinwheels Table Runner
16 inch x 42 inch
Decorating for Christmas? I originally shared this on the AccuQuilt blog last year and thought I would share it here in case you missed it. Today’s table runner would be perfect for the holidays. I pulled out a few decorations to get you in the mood!
Let’s get started on the tutorial! Skip down a little for the rotary cutting directions.
GO! Cutting Dies:
GO! Qube Mix & Match 12 Inch Block (55778) Dies used: #2 – 3 ½” Square, #5 – 3″ Half Square Triangle, #8 – 3 ½” x 6 ½” Rectangle
GO! 12 Inch Companion Set Die used: #9 – 3″ x 6″ Chisel
Materials Needed: I used batiks from Island Batik
- Cream – fat quarter
- Red – 1/3 yard (includes binding)
- 4 Assorted Red – fat quarters
- Cut 12 – Cream #5 Half Square Triangles (HST)
- Cut 12 – Assorted Red #9 Chisel
- Cut 24 – Assorted Red ##8 Rectangles
- Cut 6 – 4 – Assorted Red #2 Squares
Assembly: Sew with a 1/4 inch seam allowance.
Sew the cream half square triangles to the assorted red chisel rectangles following the diagram below. Make 12 of these. Add a red assorted print rectangle to the right side of each of the rectangle/chisel pieces. Make 12. Your sections will measure 6 1/2 inches x 6 1/2 inches.
Layout the sections as shown below to make your Christmas pinwheel blocks and sew them together.
If you would like to make the Christmas Pinwheels Table Runner and don’t have the AccuQuilt dies and cutter:
I would recommend cutting all 3 1/2″ x 6 1/2″ rectangles instead of the Chisel rectangle. Dig into your stash and use an assortment of red fabrics.
- RED – Cut 40 – 3 1/2″ x 6 1/2″ rectangles.
- RED – Cut 4 – 3 1/2″ x 3 1/2″ squares.
- CREAM – Cut 12 – 3 1/2″ x 3 1/2″ squares.
Place the 3 1/2″ cream square on top of the red rectangle.
Mark a diagonal line and stitch just a little bit to the right of the line toward the corner – fold it over.
Trim off the excess leaving a 1/4″ seam allowance.Continue following the rest of the tutorial.
You can see the way the pieces of the block go together.
You will have three 12 1/2 inch x 12 1/2 inch blocks.The border uses 4 – 3 1/2 inch squares and 16 – 3 1/2 inch x 6 1/2 inch rectangles.I forgot to take a photo of adding the border so I have included this graphic.
Sew 2 – 3 1/2 inch x 6 1/2 inch rectangles together. Make 8 of these. Follow the diagram below to add them to your blocks.
I did not add borders to the length of the table runner as it would have made it too large for my table. If you would like your table runner to be 48 inches long then add the borders. You will have enough fabric for and additional 4 – 3 1/2 inch x 6 1/2 inch rectangles and 4 – 3 1/2 inch squares.
Add your batting and backing and quilt as desired.
Cut three – 2 1/2 inch strips by the width of fabric for your binding. Bind your table runner and it is ready to place on your table for the holiday!
I hope you have enjoyed this tutorial and if you make a Christmas Pinwheels table runner please share a photo of it!
FREE PDF TO MAKE THE CHRISTMAS PINWHEEL TABLE RUNNER
Christmas Pinwheels Table Runner Tutorial
I use affiliate links. At no additional cost to you, when you make a purchase I may get a small commission. Your support is very appreciated. Thank you!
Download this free quilt pattern Snow Much Fun
|Special new one daily!||Check out the Quilt Supplies at Craftsy!|